Part Type : LED driver

Description : 80W-2100mA Constant Current

                       0-10V Dimmable

Part Number : SLI 80-I2100 120-277 W D1 M

1. Input Requirement

1.1 Input Voltage

      The nominal input voltage is 120-277VAC

      Operating Range: 108-305VAC

1.2 Frequency

      The nominal input frequency is 50Hz/60Hz

1.3 Current

      The maximum input current is 0.8 Amp at 120Vac at max output load of 2100mA.

1.4 Efficiency : The typical efficiency (watts out / watts in) is 85.5% @120V and 87.5% @277V with rated load.

1.5 Power Factor

@ 277VAC, >0.9

@ 120VAC, >0.9

1.6 Inrush Current

120VAC @ 25 DEG C: <35Amp peak

1.7 THD

THD: < 15% @ 25oC 108-305VAC, full load (w/o Dimmer)

2. Output Requirements

2.1 Output Current Setting

      Set nominal current at this voltage.

2.2 Output Voltage Range

      Driver must work at these voltages.

2.3 Output Line Regulation

      With output clamped to below set points, vary input from 108-305VAC.

2.4 Current Stability : +/- 5% maximum after 8 hours

2.5 Max Rated Output Load

2.6 Ripple Factor

      Measured at max rated load and electronic load connecting to the output is ser as below : Vd=38V Rd=0.08

      Ripple factor<5% (Ipk-pk/2/Imean).

2.7 No Load Voltage

      Not to exceed <58VDC.

2.8 Turn on Delay

      Measured @ 108-305VAC max rated load: <0.75 S

3. Protection Requirement

3.1 Short circuit protection:

      When operating under any line condition into a short circuit condition for an indefinite period of time, the power supply shall be self recovering when fault condition is removed.

3.2 Over-current protection:

      When operating under any line condition into any over load condition for an indefinite period of time, the power supply shall be self recovering when fault condition is removed.

4. Environmental Conditions

4.1 Operating

      The power supply shall be capable of operating continuously in any mode without performance deterioration in the following environmental

conditions:

4.11 Ambient Temperature: -20 to 55 Deg C. 100% rated power at 55 Deg C.

4.12 Case Temperature&Class P

4.13 Relative Humidity: 5 to 95%, non-condensing

4.14 Cooling:Convection

4.2 Non-Operating

     The power supply shall be capable of standing the following environmental conditions extended periods of time, without sustaining electrical or mechanical damage and subsequent operational deficiencies.

4.2.1 Ambient Temperature: -40 to 85 Deg C.

4.3 Shock & Vibration:

      MIL-STD-810G Shock Method 516.6 procedure IV and Vibration Method 514.6 Procedure I, Category 4

5. Reliability

5.1 MTBF

      >300,000hrs calculated to MIL-HDBK217F @ 25 DEG C. rated load. Ground Benign.

5.2 Product Life

     >5yrs @ Tc= 85 Deg C, rated load.

6. EMC

6.1 Conducted:FCC Part 15 Class B

6.2 Audible Noise: Class A sound rating not to exceed 24dBA (audible) when installed in fixture and such fixture is installed in its normal use. The measurement is to be made from a distance not less than 3 feet.

6.3 ESD: IEC 61000-4-2 Level 2: 4KV Air and Contact.

6.4 Input Transient Protection

Power supply shall comply with IEEE C.62.41-1991, Class A operation. The line transient shall consist of seven strikes of a 100 kHz ring wave, 2 kV level for both common mode and differential mode.

7. Safety

7.1 Agency Approvals

UL 8750-LED equipment for use in lighting product

UL1310-CLASS 2 Power units

CSA C22.2 No. 250.13-12-LED equipment for lighting applications

8.Dimmable

8.1 0-10V Dimming

      0-10V Input Signal: 0-10V

      Dimming Range:5-100%

9. Mechanical

9.1 Materials

Metal case

All material to be ROHs compliant to Directive 2002/95/EC

Wires to be Stranded with UL approval

Input: Black & White : 320mm , 18AWG 105℃ 600V Stranded wire

Output: Red & Black : 320mm , 18AWG 105℃ 600V Stranded wire

Dimming: Purple & Gray:530mm , 18AWG 105℃ 600V Stranded wire